Wednesday, June 8, 2016

Janome Coverpro 1000cpx Binding Tutorial using industrial binders

IMG_0188

I sew with knits a lot and by alot I mean almost exclusively!. So it's no wonder I had to have a coverstitch machine. I ended up purchasing a Janome Coverpro 1000cpx coverstitch machine with a table. It's a wonderful machine for coverstitching on knit fabrics.  It is finicky with its settings and as such a little bit of a pain in the behind to learn how to bind with it.  I never purchased the original plate and binder as I felt it was insanely overpriced.

IMG_0225

You can use industrial binders on the machine you just need a way of attaching them to the bed of the machine. You can use the original binder plate that comes together with a binder available through Janome dealers, you can buy one on ebay through Sharp Sewing Supply or through NgoSew on ebay, or you can make your own plate to hold the binder onto the machine bed or use sticky tack and adhere it to some sort of table. (Note: I've never used the plate through the dealers or sharps or Ngosew so use it at your own risk) The above photo is of the binders I own. There are different types of binders available. For our purposes we will discuss A and B binders.
Janome coverpro with generic binder

A binders are used exclusively for knit fabric as they leave a fold on the top of the binding and the underside of the binding is the raw edge that is encased in the backside of the coverstitch. It's a great choice for knits as it creates less bulk (esp. at seams). B binders double fold on both sides of the binding. I prefer using the B binders on my treadle machine using bias binding. You can use B binders on the coverstitch machine and use a chain stitch but I haven't as of yet because I'm unsure how long a chain stitch would hold up to consistent pulling esp. at the neckline.

IMG_0230

I've owned my cover pro for over 5 years now and for most of that time I used sticky tac to adhere it to the extension table. It honestly works nicely even if it's really tacky looking. Recently my children can't seem to leave my sticky tac alone and are constantly stealing it. So I changed my setup to include a metal plate I picked up at the hardware store. The holes on the metal plate were centred perfectly to match the holes of the bed of the cover pro (the first set of holes to the right of the needle). I just had to increase the size of the holes a tiny bit. I had to purchase a drill bit to drill through the metal. I used the white screws that came with the machine to adhere the metal plate to the bed of the machine. Then adhered the binder to the metal plate with bolts and screws and washers.  I honestly prefer the sticky tac the most as the binder can rest closer to the foot of the machine and it's quicker to remove and set up. I also use the clear foot for my machine as it gives me better visibility. There are various sizes in both of the A and B binders. I use the 3/8" finished A binder the most. The cut size is the size you cut the binding before it passes through the binder. I cut my binding 1 1/8". However the thinner the fabric the more you might have to cut it. a finer jersey can be cut wider and spray starch applied to it to prevent it from curling. Stabilizing it with a tricot interfacing may help and I'm currently experimenting with it. For beginners I suggest baby rib knit fabric to use as the binding material. The rib knit is just cut straight (it doesn't have to be cut on the bias) it should be cut with a rotary cutter and ruler though as it does have to be precise.

IMG_0155

The two top screws on the binder adjust the top and bottom brackets on the binder. When lining up the binder, the bottom binder bracket should be slightly to the right of the left needle. I have my bottom bracket pushed all the way to the right (as far as it goes). The top bracket is about 1/8" to the left of the left most needle. Once you've threaded the binder and pulled it to the back, the folded binding should rest between the metal parts on the clear foot. It is very important to go slow with this setup because the binding can shift as the binder isn't as close to the foot as it should be. This is why I prefer using sticky tac to adhere it to my extension table.

IMG_0189 
The top settings are 2.5 Orange needle and 4 blue needle. the looper is set at 3 but reduce the tension down to 1 over the seam - go slow over seams. 
IMG_0190
the slider is to the right and the differential feed is set to 0.5 and the stitch length 4.

IMG_0169

Always test your binder first with scrap fabric. When everything is right adhere seam stabilizer to both shoulder seams (you can use clear elastic as well to stabilize or a knit/tricot stabilizer - if using the knit/tricot stabilizer you only have to apply it to the side that touches the feed dogs so it doesn't stretch/distort the seam).  Sew/serge only 1 shoulder seam.

IMG_0156

With right side of fabric facing up put the fabric into the middle of the groove and sew the entire neckline reducing the tension of the looper down at the seam. 

IMG_0168

Baste the ends of the bindings (right sides together) with your sewing machine.


IMG_0171

Using a small crochet hook weave in the ends and then tie a knot.

IMG_0195

Tack down the seam you just sewed and tie off your ends.

Saturday, January 23, 2016

Ottobre 4/2007 #29 Corduroy Pants/Jeans

Here's some pants I made for ds#1. They were made in size 122cm with 5/8" seam allowance added. I believe I added a few 2-3" to the length so that I can lengthen them when the time comes as ds#1 is growing like a weed. The only thing I messed up on was the pocket (which I should have made 1/4" seam allowance as the 5/8" sa is to high and as a result he can't actually use the pockets. I realized after I had sewed the side seams this and at that point I wasn't willing to seam rip to fix my mistake.

IMG_3710

Here's a more unclose view of the the pocket detailing. The front leg portion has a 3 piece pattern split around the knee. I really do like the look of it especially with the corduroy as the lines add dimension to the finished pants. However its not the easiest pattern especially for a beginner. 


IMG_3711


IMG_3302


IMG_3713

The above photo shows the beautiful topstitching of the pants that gives it a more RTW look and feel.  I used my snap press dk-98 Kam press to add the nipple rivets to. I purchased the rivets from Dot Gas which is a wholesale supplier that sells to the general public. They're prices aren't that amazing but I ran into limited options for nipple rivet dies. I live in Canada and as such shipping costs are insanely high from the US to Canada. So I purchased the dot gas adapter so my snap press can use industrial dies and then that way I can use industrial die sets in the future. The clear plastic box houses the adapter piece and the industrial die set for the dk-98 press. In future, I hope that the Grommet Mart nipple rivets will work with my press. I didn't want to have to buy another press and the dies from Grommet Mart are insanely overpriced not to mention the cost of shipping would have been  about equal to what I purchased for the adapter and rivets anyways.

I also purchased some more dies to my dk-98 from Kam Snaps. I actually originally purchased my press from them. I'm not that happy though that they are discontinuing the metal dies for the press hence the reason I purchased so many at once. I purchased the 7mm grommet die, Utility spring #20, and fashion spring #20. They are good quality dies and I do like my press just really upset with their business practice of discontinuing the dies for the machines that they carry. The good thing I learned through it all is that once you buy the die sets you can usually find the hardware for them to fit. They were out of stock on the #20 fashion spring hardware so i purchased the die and looked on ebay to find something that fit. I purchased the hardware from this guy on ebay, the price was cheap enough to see if they worked and they did plus the shipping doesn't kill you to Canada.

I have stummbled across another company that sell hardware/presses and lots more of it than Kam snaps. Goldstartool  also carries snap presses. Their die sets are cheaper and looks quite similar to the dk-93 kam snap press. It's dies are screw in not flat shank so I'd have to purchase the press. I'm seriously considering purchasing their machine and corresponding die sets as they carry a wide assortment of hardware. I can't believe the rollarcoster I've had for one machine that does it all. Sadly I don't think there's such thing especially when I still have to take into consideration the cost of the dies/hardware and their shipping costs. I don't regret buying my Kam snap press as I still have the ability to buy wholesale industrial die sets and their corresponding hardware.


IMG_3136

I also modified the pattern to add an adjustable waistband just like in RTW kids clothing. Below is a photo to show you what I mean. I also didn't have any button hole elastic on hand so I used knitted elastic and just slit some openings in it. I then hemmed the pants using my blind hemmer (industrial machine) so that I can easily lengthen them when ds#1 grows.


Bob Bermudas - design change